arduino GPRS autonomous water meter data logger

Cerrado Publicado Mar 7, 2013 Pagado a la entrega
Cerrado Pagado a la entrega

== Arduino GPRS autonomous water meter data logger ==

Looking for an experienced arduino programmer with gprs experience and some hardware knowledge to write a sketch for me and provide general advice on deployment.

Hardware to be used: Seeduino stalker v2.3 / seeed GPRS shield / Seeed 6A LiPo battery / Seeed 3W Solar Panel / Sensus HRI

The sensus HRI is a battery powered semi-intelligent pulse generator with two wired outputs and a common ground; pulse and a boolean anti-tamper/error status. A full spec will be provided.

== Core software functionality ==

- Logger to collect meter pulses (int) and error status (boolean) and save them with a timestamp after p1 period (eg 5 min) as a simple count since last timestamp and cumulative count since time began.

- Transmit collected data in json / cosm format (as a PUT) every p2 period (eg hourly) to client defined HTTPS URL

- Operate as much as possible in a power saving mode consistent with continuous autonomous operation on solar power.

- No data to be lost (eg in case of failed communications or some other response besides a 200 OK, data is cached until proper communication resumes)

== Additional software functionality ==

1) Seeduino Temperature, battery voltage and charging status to be included in data transmission

2) At every data transmission also perform a POST request to a client defined HTTPS URL, the response may contain one or more parameters (in a format to be agreed) which will adjust various settings in the device, including:

- Device ID

- API key (ref. COSM API)

- title (ref. COSM API)

- id (ref. COSM API)

- The PUT and POST urls

- RTC time corrections

- p1 and p2 periods (in seconds)

- cumulative count corrections

== The successful bidder will be required to ==

- First scope the project, recommend hardware or functionality changes if necessary.

- Write a sketch with the agreed functionality which will work on the agreed hardware.

- Provide some advice on deployment.

== Deliverables ==

- Sketch which will work with the above hardware.

- If necessary, provide some advice on deployment.

- Provide advice on connecting the pulse sensor.

Arduino Programación en C Ingeniería eléctrica Electrónica Microcontrolador

Nº del proyecto: #4310547

Sobre el proyecto

11 propuestas Proyecto remoto Activo Apr 13, 2013

11 freelancers están ofertando un promedio de £558 por este trabajo

MikroStar

hi, i am an electrical engineer and an embedded system developer. i can help you with this project.

£3000 GBP en 75 días
(75 comentarios)
7.8
yhaat

Hi, I can do this job.

£250 GBP en 20 días
(42 comentarios)
5.6
nisssal

I'm experienced with Arduino and GPRS. I can do this project.

£180 GBP en 14 días
(9 comentarios)
5.0
Thesmarttechies

Dear Sir, We have more than 5 years of experience in Microcontroller, Embedded system, Sensors, Product Manufacturing, PCB Designing and developing. We can do your project very well. Please check your PM For more detai Más

£200 GBP en 14 días
(1 comentario)
2.8
k0der

please check my pm

£150 GBP en 5 días
(1 comentario)
0.0
matlabstorm

Hi; i'm newbie in freelancer but i'm sure i'm the best candidate for this project i'm working on security systems using auto call and GPRS,GPS and IMU for detecting position and any movement for the object. and hope Más

£200 GBP en 6 días
(0 comentarios)
0.0
maksmusings

I can do it.

£200 GBP en 5 días
(0 comentarios)
0.0
javierbarriga

Hello Ricardmh, I could collaborate with you in GPRS comms. Best Regards, Javier

£200 GBP en 20 días
(0 comentarios)
0.0
brettjnelson

Have recently written an embedded communication layer in C for data over cell modems. The bid does not include hardware required to test and debug the project.

£1206 GBP en 35 días
(0 comentarios)
0.0